Misc. where buy motorcraft 2100?
fieldofdreams
Jeeper
Can anyone tell me where to purchase a motorcraft 2100 carb for my Cj? Thank you, any help is appreciated!
Misc. where buy motorcraft 2100?
- Thread starter fieldofdreams
- Start date
Manic Mechanic
Full Time Jeeper
- Posts
- 1,586
- Thanks
- 359
- Location
- Thurmont MD
- Vehicle(s)
- 85 CJ7 4.2L 258 .040 over, T-5 trans, dana 300, dana 30 front 3.23 and lock right locker, rear amc 20 3.23 one piece axle shafts traclock
79 CJ7 304, th400 auto borgwarner 1389?? qudratrac stock rest unknown.
89 YJ 4.2L 258, AX-15 5spd, NP231, dana 30 front, dana 35 rear with posi, gears unknown
92 YJ 4.0, AX-15 5spd, np231, dana 30 front, dana 35 rear.
google comes up with aftermarket units.
junkyards, ebay, swap meets, etc etc etc.
look for one with 1.08 Venturi (sp) common on the 72 bronco with the 302.
Sent from my E6810 using Tapatalk
junkyards, ebay, swap meets, etc etc etc.
look for one with 1.08 Venturi (sp) common on the 72 bronco with the 302.
Sent from my E6810 using Tapatalk
- Posts
- 5,832
- Thanks
- 74
- Location
- Plumas Lake, CA, USA
- Vehicle(s)
- 1974 CJ5 ~ Fresh built AMC 360 - SM420 - D20 - D30F with upgraded 30 spline shafts and knuckles & D44R - 4.27 Gears - ARB Lockers F/R - All chrome molly axles - on 33's - YJ 4" Lift Spring Conversion
There was a guy on amazon in Colorado I've had luck with a few times now. They're reman units, or aftermarket most of the time. But they bolt on and run no issues. Little tuning from there.
Figure out CFM needs and match as close as you can. Also jet sizes may need some tweaking. Choke style, and some models have elevation adjustments (2150 I believe?).
Elwood Blues had some good write ups on here for 2100's / carbs.
If you go junk yard - eye the normal vac leak areas. if the throttle plate shaft has too much slop / play, find another or plan on sleeving it.
Mike's carburetor is also a goo place for rebuilds / parts I believe. https://www.carburetor-parts.com/ lots of info and knowledge there...
Cheers
Figure out CFM needs and match as close as you can. Also jet sizes may need some tweaking. Choke style, and some models have elevation adjustments (2150 I believe?).
Elwood Blues had some good write ups on here for 2100's / carbs.
If you go junk yard - eye the normal vac leak areas. if the throttle plate shaft has too much slop / play, find another or plan on sleeving it.
Mike's carburetor is also a goo place for rebuilds / parts I believe. https://www.carburetor-parts.com/ lots of info and knowledge there...
Cheers
TnCJ
Senior Jeeper
- Posts
- 566
- Thanks
- 6
- Location
- South East Tennessee
- Vehicle(s)
- 1980 CJ 5, 4.2 engine, D30,AMC 20, T176, Dana 300, MC 2100 carburetor.
I got mine from this guy but looks like he is out of stock.
https://www.ebay.com/p/1223345683
https://www.ebay.com/p/1223345683
fieldofdreams
Jeeper
Thank you! You guys are great