Body Jeep insignia on a fiberglass tubu
Body Jeep insignia on a fiberglass tubu
- Thread starter Gary W
- Start date
- Posts
- 7,316
- Thanks
- 156
- Location
- Roanoke, Va
- Vehicle(s)
- '80 CJ-7, AMC 304, T177, Dana 300, Widetrack axles (D30 & AMC20) w/ 3.73 gearing, MSD ignition,
Greetings from Roanoke!! Welcome aboard....
As for the raised lettering, in don’t know if there’s anything you can do without a good bit of trouble. A silicone cast of the lettering would allow making some out of fiberglass resin - you could glue em on. Otherwise, the vinyl lettering is about it.
Sent from my iPhone using Tapatalk
As for the raised lettering, in don’t know if there’s anything you can do without a good bit of trouble. A silicone cast of the lettering would allow making some out of fiberglass resin - you could glue em on. Otherwise, the vinyl lettering is about it.
Sent from my iPhone using Tapatalk
Belizean
Always Off-Roading Jeeper
- Posts
- 6,081
- Thanks
- 414
- Location
- New Orleans area
- Vehicle(s)
- 84 CJ7 4 banger-owned since new in 1984 bought off truck at dealership - rebuilding 258, T176 with Sniper EFI D300 4:1 Lomax gears Twin Sticked 1 piece axels with locker
Maybe a good ole faction branding iron with the Jeep logo.
- Posts
- 7,316
- Thanks
- 156
- Location
- Roanoke, Va
- Vehicle(s)
- '80 CJ-7, AMC 304, T177, Dana 300, Widetrack axles (D30 & AMC20) w/ 3.73 gearing, MSD ignition,
Seems I have seen a few of the newer Jeeps with raised letters........ don’t remember which model.
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
- Posts
- 7,316
- Thanks
- 156
- Location
- Roanoke, Va
- Vehicle(s)
- '80 CJ-7, AMC 304, T177, Dana 300, Widetrack axles (D30 & AMC20) w/ 3.73 gearing, MSD ignition,
I wouldn’t wanna be the sucker holdin it down while it’s being branded
Sent from my iPhone using Tapatalk
- Posts
- 7,316
- Thanks
- 156
- Location
- Roanoke, Va
- Vehicle(s)
- '80 CJ-7, AMC 304, T177, Dana 300, Widetrack axles (D30 & AMC20) w/ 3.73 gearing, MSD ignition,
This is what I was thinking of....... these are used and would need new adhesive. A new set would be best. They’re chrome - but I’d think some scuffing and some satin black paint they’d be good to go.
https://www.ebay.com/itm/142463024963?hash=item212b753f43:g:Pw8AAOSw8FtZgKkW
Sent from my iPhone using Tapatalk
https://www.ebay.com/itm/142463024963?hash=item212b753f43:g:Pw8AAOSw8FtZgKkW
Sent from my iPhone using Tapatalk
- Posts
- 7,316
- Thanks
- 156
- Location
- Roanoke, Va
- Vehicle(s)
- '80 CJ-7, AMC 304, T177, Dana 300, Widetrack axles (D30 & AMC20) w/ 3.73 gearing, MSD ignition,
According to the description, they may be a bit smaller than the vinyl letters, but no by much
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
- Posts
- 7,316
- Thanks
- 156
- Location
- Roanoke, Va
- Vehicle(s)
- '80 CJ-7, AMC 304, T177, Dana 300, Widetrack axles (D30 & AMC20) w/ 3.73 gearing, MSD ignition,
Then again, appears they are exactly the same size as the vinyl letters.....
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
Nice! I really like that!. Cant tell how big they are , you think theyre similar sito CJ
Shum8 I appreciate the tip, I went ahead and ordered both side. For $30 cant go wrong! Thx!Then again, appears they are exactly the same size as the vinyl letters.....
Sent from my iPhone using Tapatalk
- Posts
- 7,316
- Thanks
- 156
- Location
- Roanoke, Va
- Vehicle(s)
- '80 CJ-7, AMC 304, T177, Dana 300, Widetrack axles (D30 & AMC20) w/ 3.73 gearing, MSD ignition,
Gonna leave em chrome or paint em? Post up pics when you’re done
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk