Steering Hydro assist steering mounts.
Steering Hydro assist steering mounts.
- Thread starter coldair
- Start date
j6824
Senior Jeeper
- Posts
- 527
- Thanks
- 57
- Location
- Central Virginia
- Vehicle(s)
- '78 CJ5, 258, D30, AMC 20, 3.54, T150, 33s, Sniper EFI, 4"BDS, 1" M.O.R.E. body, Team Rush, MDS 6A, BDO tie rod flip, Adams shafts, Speedhut gauges, 8274
Been looking at this myself here lately...have come across a few examples
This may be similar to your specific setup: https://irate4x4.com/threads/advice-on-mounting-for-psc-cylinder-79-scout-ii-soa-w-high-steer.45194/
This may be similar to your specific setup: https://irate4x4.com/threads/advice-on-mounting-for-psc-cylinder-79-scout-ii-soa-w-high-steer.45194/
shooby
Jeeper
- Posts
- 121
- Thanks
- 14
- Location
- Lincoln Nebraska
- Vehicle(s)
- 1978 CJ5
360 V8, T18,D20,Teralows,D30 w/OX, AMC 20 w/OX, 1 piece Moser, 33"BFGs, Howell TBI, Mallory HEI
CJ
Admin
- Posts
- 21,716
- Thanks
- 622
- Location
- Central FL
- Vehicle(s)
- '72 CJ5, 401, T18, D20, D44, D30
'82 CJ8, 258, D300, AMC20, D30
Nice, that's some creaky suspension... 
shooby
Jeeper
- Posts
- 121
- Thanks
- 14
- Location
- Lincoln Nebraska
- Vehicle(s)
- 1978 CJ5
360 V8, T18,D20,Teralows,D30 w/OX, AMC 20 w/OX, 1 piece Moser, 33"BFGs, Howell TBI, Mallory HEI
Nice Louvers!
I think imma just copy what you do lol
Sent from my iPhone using Tapatalk
CJ
Admin
- Posts
- 21,716
- Thanks
- 622
- Location
- Central FL
- Vehicle(s)
- '72 CJ5, 401, T18, D20, D44, D30
'82 CJ8, 258, D300, AMC20, D30
That looks good. That CJ is going to be so much easier to wheel soon... 
looking good
CJ
Admin
- Posts
- 21,716
- Thanks
- 622
- Location
- Central FL
- Vehicle(s)
- '72 CJ5, 401, T18, D20, D44, D30
'82 CJ8, 258, D300, AMC20, D30
Almost to Moab!
77-7 TRAX
Jeeper
- Posts
- 3
- Thanks
- 1
- Location
- Oregon, USA
- Vehicle(s)
- 1977 CJ7, 256, T18, D20, AMC20, D30, TDC Frame, PSC Hydro-assist, Mattracks 105s
Where did you mount your PS fluid reservoir. Mine I mounted on the Head bolt/studs. I made a bracket out of scrap aluminum "I" beam I cut down and fashioned into a bracket with adjustment slots to be able to move the reservoir when changing belt. I am still working the install on my 77 CJ7. Very interested in your progress. The additional bracket attached is for the fuel pressure regulator.
77-7 TRAX
Jeeper
- Posts
- 3
- Thanks
- 1
- Location
- Oregon, USA
- Vehicle(s)
- 1977 CJ7, 256, T18, D20, AMC20, D30, TDC Frame, PSC Hydro-assist, Mattracks 105s
Looks like your bracket would fit more engine setups than mine. Mine engine is somewhat missing emissions hardware plus I didn't have my drivers fender on when I dreamt up my bracket. I like what you came up with and I may have to change mine some day. For now it's an off-road vehicle. Lol
coldair
Full Time Jeeper
- Posts
- 2,441
- Thanks
- 13
- Location
- wyoming
- Vehicle(s)
- 1986 cj7 in the works,
1996 F350 crew cab with a 5.9 cummins
It took me a while to come up with what you see. I worked out a few brackets but never liked them. This is the best I have built so far. Might rework it after this years moab trip. We will see.
Attachments
77-7 TRAX
Jeeper
- Posts
- 3
- Thanks
- 1
- Location
- Oregon, USA
- Vehicle(s)
- 1977 CJ7, 256, T18, D20, AMC20, D30, TDC Frame, PSC Hydro-assist, Mattracks 105s
Thanks for posting the pictures. It makes it easier for us all. The brackets required for any of the upgrades can be daunting to build especially with no examples to go by. If I have to reassemble the emissions on my engine I will have to rework my bracket I suppose. Thanks for the reply. I'm new here so I really appreciate the feedback. I haven't addressed the ram setup yet but will be watching your progress for ideas.