temp

  1. A

    Electrical Factory water temp gauge setup?

    I have a 1985 CJ7 with a 258. Much of the engine wiring has been modified from stock and I'm trying to remove the hacked-on aftermarket stuff and get the factory gauges working again. I'm trying to figure out exactly how I should be setting up the factory water temp gauge. What does the factory...
  2. B

    Stewart Warner Gauges Update 1/6/20

  3. JeeperChris

    Where is my temp sending unit??

  4. RiverandSand

    Working temp gauge

  5. Tectron

    Temp gauge wiring

  6. J

    Temp sensor in CTO port

    I recently acquired a '78 CJ-7 with the 258. The factory gauges are either inoperable or untrustworthy so I bought a Bosch 3-gauge set from a local parts store, only to find that the aftermarket sensor will not fit into the factory sensor port. The 3-port CTO fitting on the side of the block is...
  7. J

    Temp sensor in CTO port

  8. J

    Engine temp hacks? Gauge broken, engine running HOT (maybe?)

    I'm getting the sense that my engine is running FAR too hot. It’s my daily driver for the 4-mile hike into work and it the heat it produces is the point I can barely touch the hood to open it up. The problem is, neither I or the PO could get the dashboard’s engine temp gauge to work. The...
  9. J

    Engine temp hacks? Gauge broken, engine running HOT (maybe?)

  10. K

    Fuel and Temp Gauge

  11. JeffP

    Easy Mechanical Temp Gauge

    I’ve heard many Jeep owners either ask or complain about connecting a mechanical water temp gauge... the typical sensor probe won’t fit. The simple solution is a brass fitting and pipe nipple available at Ace Hardware. The first is a Bell Reducer, 1/2” FIP / 3/8” FIP. Lasco Brand #17-9281 34FD...
  12. JeffP

    Easy Mechanical Temp Gauge

  13. Mpeaden

    Water Temp Sender and Gauge Conversion

    Hello All!! new to the forum Recently purchased a '79 CJ5 with an '82 Chevy C10 350 block I'm wanting to keep the original speedo cluster which contains the water temp gauge inside. I've found that the water temp sensor for the 350 is quite a bit larger and the ohms are waaaaay off from the...
  14. Mpeaden

    Water Temp Sender and Gauge Conversion

  15. boney

    Gas and Temp gauges: down the rabbit hole I go

  16. jzak

    Mech. Temp Gauge Stopped Working!

  17. B

    Fuel and Temp gauge No power?

    I have searched and read many threads about testing fuel gauge troubles. My problem is that there is no power at the fuse for those gauges. From where does the power enter the fuse block and has any one experienced and resolved this problem before? I also have no power to the fuse for the...
  18. J

    Coolant temp sensor location.

    Installing a EFI kit on my 4.2 and I need to install a new coolant sensor I'm not sure where in the block it goes. I have searched and cant seem to find a picture showing the location. I need to install a coolant sensor other than the one on the top of the block next to the valve cover. Thanks.
  19. J

    Coolant temp sensor location.

    Installing a EFI kit on my 4.2 and I need to install a new coolant sensor I'm not sure where in the block it goes. I have searched and cant seem to find a picture showing the location. I need to install a coolant sensor other than the one on the top of the block next to the valve cover. Thanks.
  20. N

    Replace clock with water temp gauge

    Can someone tell me what size gauge is needed to fit in the dash to replace the clock? I know the oil and volts gauge is 2". Merry Cristmas everyone. 1986 CJ7
Back
Top Bottom
AdBlock Detected

I get it, I'm a Jeep owner and ad-block detectors kinda stink but ads are needed on this site. This is a CJ site, all the ads are set for autos (some times others get through.) I cannot make them just for Jeeps but I try.

Please allow ads as they help keep this site running by offsetting the costs of software and server fees.
Clicking on No Thanks will temporarily disable this message.
I've Disabled AdBlock    No Thanks