studs

  1. Masscj7

    Wheel studs

    Anyone know if front and rear wheel stubs for the Dana 30 and AMC 20 rear are the same? I can imagine they wouldn’t be? Had a Homer Simpson moment and need to replace some missing fronts (all so have none to compare) and I have some spare rears. Sent from my iPhone using Tapatalk
  2. N

    Power steering pump studs

    I bought a replacement power steering pump for my 85 CJ7 (2.5L engine) and in a moment of stupidity took back the old one for core refund before installing the new one. Turns out the studs on the back of the new pump are too short to go through the mounting bracket, and the store already shipped...
  3. S

    convert intake and exhaust manifolds to studs from bolts?

    I am upgrading my '80's intake and exhaust manifolds to a newer models' that arent bolted together. I am getting them for close to free from a friend. I have seen people talk about converting to studs from bolts. based on my searches and reading, there are already two studs for alignment of...
  4. S

    convert intake and exhaust manifolds to studs from bolts?

  5. B

    258 cylinder head bolts or studs

    I'm replacing the head gasket on the 258 and plan to buy new cylinder head bolts. My valve cover is aluminum. Head studs were used on the driver side with nuts used on these studs also to help secure the valve cover. If I get the ARP head bolts and not use studs on drivers side, will I be...
  6. B

    258 cylinder head bolts or studs

  7. C

    CJ7 Lower side moulding studs?

    I'm trying to find a source for the studs used to mount the aluminum, lower side mouldings on my CJ7. I need 8 in total, the last owner seemed to have lost them. They are threaded studs attached to small plates, allowing them to slide in the grooves, cast on the back-side of the mouldings...
  8. CJim7

    And THIS is what I found.....

    Just prior to my CJ deciding it wanted to quit running, I had it out for a little drive and noticed a "clunking" coming from the rear end. Not just the sound, but you could feel it (almost like a flat tire, but not that dramatic) So last night I decided to tear into the rear end. At this...
  9. CJim7

    And THIS is what I found.....

    Just prior to my CJ deciding it wanted to quit running, I had it out for a little drive and noticed a "clunking" coming from the rear end. Not just the sound, but you could feel it (almost like a flat tire, but not that dramatic) So last night I decided to tear into the rear end. At this...
  10. C

    Spindle studs source?

    Opened up the front rotor to check the bearings and the spindle bearing. Appears the PO stripped out 3 of the 6 spindle studs that holds the spindle. Instead of replacing with new studs they used 1" 3/16 grade 8 bolts. To keep them from vibrating out (I'm assuming from this point) they taped 2...
  11. T

    Manifold studs

    Ive developed an exhaust leak on one cylinder. I suspect its from a missing stud in the very rear but after taking a pic Im not sure if there was one to start with. I cannot even get a look due to location but the pic I took looks like there is almost a clean factory hole in the head but the...
  12. T

    Manifold studs

    Ive developed an exhaust leak on one cylinder. I suspect its from a missing stud in the very rear but after taking a pic Im not sure if there was one to start with. I cannot even get a look due to location but the pic I took looks like there is almost a clean factory hole in the head but the...
  13. khass0410

    Hmm upper shock bolt studs ???

    Are starting to be a pain in the flippin :D ........Anyways I now hate anything to do with suspensions I am running into problem after problem. So my deal is simply this I do believe that the threads on these studs are stripped ran out or what ever so this is what I'm thinking about doing...
  14. FiNorman

    Broken lug studs

    While removing the oversized tire of of the jeep I broke off two of the lug bolts holding the wheel. I am going to convert my drum brakes to disc brakes anyway using this method AMC 20 disk brakes Therefore I know I need to save some of the old backing plate, but I'm having trouble figuring...
  15. S

    Change from bolts to studs

    I have a 1973 cj5 with warn hubs that the bolts keep backing out do the make a stud kit to replace the bolts?:confused: Thanks
  16. S

    Change from bolts to studs

    I have a 1973 cj5 with warn hubs that the bolts keep backing out do the make a stud kit to replace the bolts?:confused: Thanks
  17. hole

    Replacing Ball Studs

    Just discovered my upper ball studs are no good:( I'm sure the lowers cant be far behind. Any tips from those who have already replaced theirs?
Back
Top Bottom
AdBlock Detected

I get it, I'm a Jeep owner and ad-block detectors kinda stink but ads are needed on this site. This is a CJ site, all the ads are set for autos (some times others get through.) I cannot make them just for Jeeps but I try.

Please allow ads as they help keep this site running by offsetting the costs of software and server fees.
Clicking on No Thanks will temporarily disable this message.
I've Disabled AdBlock    No Thanks