sleeve

  1. I

    AMC 20 Crush Sleeve Eliminator Opinion

    Hey Everyone, My AMC 20 is completely torn down for a one piece axle, spartan, and pinion seal install. I was reviewing the procedure for retightening the pinion nut with the crush sleeve and wondered if anyone had converted to a crush sleeve eliminator instead? Something like this...
  2. I

    AMC 20 Crush Sleeve Eliminator Opinion

  3. F

    Dana 20 speedometer gear sleeve needed...

    Hey Jeepers, does anyone have an extra or know where I can get a Dana 20 speedometer gear sleeve? I don't know if I'm searching for it wrong but I can't find one online. It looks like this in case my nomenclature is off...
  4. F

    Dana 20 speedometer gear sleeve needed...

    Hey Jeepers, does anyone have an extra or know where I can get a Dana 20 speedometer gear sleeve? I don't know if I'm searching for it wrong but I can't find one online. It looks like this in case my nomenclature is off...
  5. raser13

    Where to get adaptor sleeve for he'd swap

    Hey guys contemplating doing ahead swap my head has 7/16 diameter bolts. The other head uses 1/2 in bolts. I've seen some mention adaptor sleeves that they use to solve this issue. Where do you get them ? Or how do you make them? Thanks for any help.
  6. raser13

    Where to get adaptor sleeve for he'd swap

    Hey guys contemplating doing ahead swap my head has 7/16 diameter bolts. The other head uses 1/2 in bolts. I've seen some mention adaptor sleeves that they use to solve this issue. Where do you get them ? Or how do you make them? Thanks for any help.
  7. A

    wont go in 1st

    Replaced bell housing, clutch fork, pivot ball and inner spring. Put it all back together and now not going into 1st (t-15, to left and down). Goes in other gears. The other thing is I have rear drive line disconnected, because need to fix rear axle. Any ideas?
  8. A

    wont go in 1st

    Replaced bell housing, clutch fork, pivot ball and inner spring. Put it all back together and now not going into 1st (t-15, to left and down). Goes in other gears. The other thing is I have rear drive line disconnected, because need to fix rear axle. Any ideas?
  9. A

    How to take off shifter.

    Do I take out all the bolts on top?
  10. A

    How to take off shifter.

    Do I take out all the bolts on top?
  11. OEM1984CJ7

    D300 yoke speedi sleeve

    Any one used a speedi sleeve for the yoke on a D300 transfer case? Not for a clocking ring but just on the drive shaft yoke. If so part #?
  12. OEM1984CJ7

    D300 yoke speedi sleeve

    Any one used a speedi sleeve for the yoke on a D300 transfer case? Not for a clocking ring but just on the drive shaft yoke. If so part #?
  13. T

    Ball joint adjustment sleeve

    Putting new ball joints in today, and when putting in the sleeve, I couldn't get it anywhere near the 50 ft/lbs of torque. It was almost halfway out the bottom before I thought something might not be right and stopped. I grabbed the old one and noticed it was thicker, which also means the I.D...
  14. T

    Ball joint adjustment sleeve

    Putting new ball joints in today, and when putting in the sleeve, I couldn't get it anywhere near the 50 ft/lbs of torque. It was almost halfway out the bottom before I thought something might not be right and stopped. I grabbed the old one and noticed it was thicker, which also means the I.D...
  15. Q

    t5 seal/transfer case sleeve

    I removed tranny and t/fer case because of leak from tranny. The input shaft of the t/fer case looks somewhat grooved and I am wondering if that is causing the leak past the tranny seal. Is there a sleeve that goes on the input shaft for this? (I am thinking like there are for harmonic...
  16. Q

    t5 seal/transfer case sleeve

    I removed tranny and t/fer case because of leak from tranny. The input shaft of the t/fer case looks somewhat grooved and I am wondering if that is causing the leak past the tranny seal. Is there a sleeve that goes on the input shaft for this? (I am thinking like there are for harmonic...
  17. billyballer

    AMC 20 Crush Sleeve problem

    I'm finally in the process of regearing the axles in my '86 CJ7. Got the standard Dana 30 front and AMC 20 rear. So I set up the AMC 20 using setup bearings, after playing around with shim stacks I got a nice pattern and now I'm going for the final install. With the new bearings, races and...
  18. billyballer

    AMC 20 Crush Sleeve problem

    I'm finally in the process of regearing the axles in my '86 CJ7. Got the standard Dana 30 front and AMC 20 rear. So I set up the AMC 20 using setup bearings, after playing around with shim stacks I got a nice pattern and now I'm going for the final install. With the new bearings, races and...
  19. T

    Dana 300 clutch sleeve question

    I've read that the clutch sleeves in the dana 300 have a front and back (ie) thick and thin flange that should go thick to large gear. How important is this. I hope not too!
  20. T

    Dana 300 clutch sleeve question

    I've read that the clutch sleeves in the dana 300 have a front and back (ie) thick and thin flange that should go thick to large gear. How important is this. I hope not too!
Back
Top Bottom
AdBlock Detected

I get it, I'm a Jeep owner and ad-block detectors kinda stink but ads are needed on this site. This is a CJ site, all the ads are set for autos (some times others get through.) I cannot make them just for Jeeps but I try.

Please allow ads as they help keep this site running by offsetting the costs of software and server fees.
Clicking on No Thanks will temporarily disable this message.
I've Disabled AdBlock    No Thanks