seal

  1. R

    Diff Wheel Seal Locking Hubs with Quadra Trac

    Rebuilding the Dana 30 on my new to me 1979 CJ7. Wheel seals should be easy. These locking hubs have been difficult. Evidently, the kit for the locking hubs comes with spindles. Those spindles use a different wheel seal than the stock parts. NAPA sold me SKF part 21159 for $22.90 per seal...
  2. T

    Body Hardtop seal replacement questions.

    So I have an existing deal that was placed in the body of the jeep and can tell it has shrunk likely due to that. I have cleaned the hardtop inside and out it preparation of the new seal install. Any tips? I believe I read to install the seal over the old seal on the front. So the pics I’m...
  3. M

    Dana 300 shift rail seal cover

    Can someone tell me what this dana 300 part is called? And also where I can find one. All the exploded view diagrams I've looked at either don't have it at all or show it but don't give a name or part number so makes me wonder how important it even is. It covers the shift rail seals. My 300...
  4. J

    1-piece axle seal cross reference part number?

    Does anyone have a part number for the AMC 20 1-piece axle seal that cross references to the Omix 3170700? Hoping I can pick one up at Autozone or the like. Parts stores today are lazy and don't want to try and match a part.
  5. V

    Hardtop windshield frame seal

  6. L

    Moser seal orientation

    Getting ready to stick the one piece Moser axles back in. The instructions are vague on which side of the seal faces in. All my experience says side "B" in the picture below faces towards the differential. Just thought I would ask here in case there is something different about Jeeps - this...
  7. L

    Moser seal orientation

  8. L

    transfer case output shaft seal

    So I'm replacing the seal on the front output shaft. As I'm taking stuff apart, I am noticing silicone behind the shaft nut and on the splines. I am assuming this was done to prevent seeping of oil through the spines. Do you think this is necessary? I have seen this done in other applications...
  9. L

    transfer case output shaft seal

  10. S

    Dana 30 Bearing / Seal Kit

    Does anyone have the Timken or Skf part#'s for bearings, seals and related parts to rebuild the hub & spindle? I'm getting ready to replace ball joints and axle u-joints and figured its a great time to refresh it all. This is on a 79 CJ5 Dana 30
  11. S

    Dana 30 Bearing / Seal Kit

  12. cglax6

    D44 inner oil seal

    All, continuing my rear axle project and I'm at another stopping point. I pulled the carrier in the diff housing, and there were no oil seals...hence why my axle tubes were filled with diff oil. For the life of me, I cannot find the correct oil seals for the inside of the diff housing...
  13. cglax6

    D44 inner oil seal

  14. Z

    CJ7 Hardtop Side Glass Seal

  15. Scout1067

    Engine seal

    I got up under my Jeep yesterday to do an oil change. First thing I noticed was the engine oil was about a quart low, it was good the last time I checked it right after Thanksgiving. When I got under it it looks like engine oil is dripping out of the bell housing. I first thought it was from the...
  16. Scout1067

    Engine seal

  17. B

    Windshield Seal - Help

  18. El Jeep o

    Hard top rear window seal

    anyone try to replace their rear window seal(gasket)? I bought one from omix ada and it does not fit well at all. even called to verify its the right one. almost seems like its a universal gasket. i would really like to get my window back in if anyone could help me.
  19. Scout1067

    AMC-20 axle seal replacement

    How much of a pain is it to do an axle seal replacement on the AMC-20 rear axle? I noticed the other day that my D/S rear axle is leaking a little from the drum. It is too thick to be brake fluid so my guess is that axle seal let go. I had this same issue on my old truck (07 Nissan Frontier)...
  20. T

    Rear main seal crankshaft issue/ need advice on next step

    Ok so I own a 1974 CJ5 that is for the most part in great condition. It was restored in 2001 by a PO and after restoration and some use it did some aging in a barn. Over the past couple years I have replaced a lot of the wearable items and gave it some TLC to get it back in reliable shape...
Back
Top Bottom
AdBlock Detected

I get it, I'm a Jeep owner and ad-block detectors kinda stink but ads are needed on this site. This is a CJ site, all the ads are set for autos (some times others get through.) I cannot make them just for Jeeps but I try.

Please allow ads as they help keep this site running by offsetting the costs of software and server fees.
Clicking on No Thanks will temporarily disable this message.
I've Disabled AdBlock    No Thanks