rocker

  1. CJ

    Harland Sharp 1.7:1 Roller Rocker Arms

    Since there are not many full roller rocker arm manufacturers available for AMC I had only a few brands to choose from for my CJ5. The ratio of 1.7:1 narrowed the field more and since I was not in the mood to fork over $400 dollars or more, Harland Sharp became my brand of choice...
  2. nitor

    Rocker guard trim

  3. D

    Factory Side Rocker Trim?

  4. L

    Floor and rocker replacement

  5. B

    Aluminum/chrome rocker trim?

  6. fastphil

    rocker panel

    Trying to find the stainless rocker panel piece between the wheel wells. Anyone know where I can find some?
  7. J

    Rusty rocker arms?

    I replaced the valve cover gasket today on my 258 and noticed the first 3 cylinders have surface rust on some of the rocker arms and bridges, None on the last 3 cylinders. There is also no rust on ANY of the push rods or springs ect and the inside of the head looks clean NO coolant or water seen...
  8. J

    Rusty rocker arms?

    I replaced the valve cover gasket today on my 258 and noticed the first 3 cylinders have surface rust on some of the rocker arms and bridges, None on the last 3 cylinders. There is also no rust on ANY of the push rods or springs ect and the inside of the head looks clean NO coolant or water seen...
  9. S

    Need new rocker arms?

    Im rebuilding my amc 304 next week. It has the stud mounted, adjustable rocker arms, not the bridged style. For those in the know, how important is it to replace them upon rebuild if they pass visual inspection? Thank you Shane
  10. S

    Need new rocker arms?

    Im rebuilding my amc 304 next week. It has the stud mounted, adjustable rocker arms, not the bridged style. For those in the know, how important is it to replace them upon rebuild if they pass visual inspection? Thank you Shane
  11. 8

    Separating floor pan from rocker

    I'm replacing the front floor pans on my CJ7 and this is my first attempt at a "body work" kind of job. The drivers side has rot all the way to the rocker so I'm going to have to separate it from the rocker. I'm assuming they are spot welded together at the lip that folds down from the floor pan...
  12. RVA CJ

    Suggestion for polishing stock aluminum rocker guards?

    The P.O. Attempted to polish the stock aluminum rocker guards off my Laredo. The swirls are pretty good. I will need to strip off the existing paint and then lightly sand, then polish. Has anyone had any experience doing this sort of thing? I'm just looking for some suggestions to avoid...
  13. D

    Rocker arm options-77' V8

    I'm rebuilding the 304 in my 77' and need to replace the rocker arms as they are used up. Is there something a little more modern to replace the originals with?
  14. D

    Rocker arm options-77' V8

    I'm rebuilding the 304 in my 77' and need to replace the rocker arms as they are used up. Is there something a little more modern to replace the originals with?
  15. B

    rocker arm question on my 4.2l

    I got my head back from the machine shop and I am re-assemblying everything.I got to the last rocker arm (towards the firewall) and it's sloppy.Ive taken it apart twice and the pushrod is seated like its suppose to be and torqued to 21ft pds. Am I doing something wrong? all the others appear to...
  16. B

    rocker arm question on my 4.2l

    I got my head back from the machine shop and I am re-assemblying everything.I got to the last rocker arm (towards the firewall) and it's sloppy.Ive taken it apart twice and the pushrod is seated like its suppose to be and torqued to 21ft pds. Am I doing something wrong? all the others appear to...
  17. C

    rocker arms problems ?

    I had a ticking in the engine took off the rocker arms and found two pushrods were bent slightly so i changed all of them. After putting everything back I started the engine and ran for a min then started knocking, opened it back up and found it snapped the bolts and the pivot/bridge in half...
  18. C

    rocker arms problems ?

    I had a ticking in the engine took off the rocker arms and found two pushrods were bent slightly so i changed all of them. After putting everything back I started the engine and ran for a min then started knocking, opened it back up and found it snapped the bolts and the pivot/bridge in half...
  19. jeepboy45

    rocker arm wear question

    Hey everyone.... I'm finishing the build on my 360 and was going to re-use the rockers, bridges, pivots and pushrods. No pushrods are bent. All bridges are the stamped out metal version, not the aluminum cast ones prone to breaking. My question is: Who here has experience in looking at...
  20. jeepboy45

    rocker arm wear question

    Hey everyone.... I'm finishing the build on my 360 and was going to re-use the rockers, bridges, pivots and pushrods. No pushrods are bent. All bridges are the stamped out metal version, not the aluminum cast ones prone to breaking. My question is: Who here has experience in looking at...
Back
Top Bottom
AdBlock Detected

I get it, I'm a Jeep owner and ad-block detectors kinda stink but ads are needed on this site. This is a CJ site, all the ads are set for autos (some times others get through.) I cannot make them just for Jeeps but I try.

Please allow ads as they help keep this site running by offsetting the costs of software and server fees.
Clicking on No Thanks will temporarily disable this message.
I've Disabled AdBlock    No Thanks