release

  1. 1

    Clutch Clutch adjustment

    Quick question, If I adjust the clutch linkage will it change the disengagement/engagement point of the pedal? Or will it only adjust the free play in the clutch pedal? My clutch is engaging and disengaging closer to the top of the pedal. I want to put the disengagement/engagement point...
  2. KeithMcKalister

    Hydraulic Release (throw out) bearing

    Does anyone have any experience with a product like this? https://www.summitracing.com/parts/ram-78130?seid=srese1&gclid=Cj0KCQjwuZDtBRDvARIsAPXFx3DCkEiQCYnzQ_NDiznxh-T3rDEQTeJTUIMxxabiwmnBEvZ6mOdAf4saAjwqEALw_wcB I'm thinking it may be a better option than fabricating my own bracket for a...
  3. Vikingone

    Bypassing the release lever.

    So after a bit of a hiatus I’m back to working on the Jeeps steering column. I was having an issue when putting back together with the key release lever not working. So took it back apart. First off I can’t tell where the spring is supposed to sit on the lower shroud. Secondly. The shroud is...
  4. O

    cj3b with V6... issue with throwout/ clutch release bearing

    Hey Everyone, So I'm trying to get me rebuilt t-90 and new clutch put back together again but the kit which I bought (LUK-04-003) came with a different throw out bearing to the original I took out. The engine is a 67 buick 225 V6. I just finished rebuilding the transmission from a T-86 to a...
  5. O

    cj3b with V6... issue with throwout/ clutch release bearing

  6. J

    Clutch Linkage: Release rod and adjuster problems

    If you’ve been following at home, I had a couple problems with my clutch linkage (driver side pivot bracket sheared off the bolts). Upon review of the linkage, bell crank, etc., it looked pretty rough so I ordered a whole new kit for $70. (Before you ask, no I didn’t get the Heim upgrade. Will...
  7. J

    Clutch Linkage: Release rod and adjuster problems

  8. T

    Key release mechanism

    Hi all, I've just purchased a 1983 CJ7 4.2L T5 300. It had not run in ten years. We've had it for two weeks and it now runs, turns and stops - still a lot to do though. As part of the work through, I decided to change the ignition switch, steering lock and turn signal switch as all three had...
  9. S

    Parking brake release cable retainer?

    Hopefully Im posting this in the right section.... I have a 73 cj5, and on top of needing new rear parking brake cables, I am needing a new clip that holds the park brake release cable assembly to the dash. Its missing, and I can't seem to find one anywhere. I have found some diagrams that...
  10. JTNCHRIS

    shudder on clutch release

    when letting out the clutch and proceeding forward, I experience a rather violent shudder. now mind you this is not an every time thing. comes and goes. any diagnosis based on description out there?
  11. JTNCHRIS

    shudder on clutch release

    when letting out the clutch and proceeding forward, I experience a rather violent shudder. now mind you this is not an every time thing. comes and goes. any diagnosis based on description out there?
  12. 1984 CJ7

    Bell crank clutch release backwards

    I just installed a new one from Morris 4x4 and realized I installed it backwards. It seems to be the same though so will it really matter? I have the grease niple towards the outside but in the illistrations, it is on the inside near the transmission. I just hate to have to redo it unless it...
  13. 1984 CJ7

    Bell crank clutch release backwards

    I just installed a new one from Morris 4x4 and realized I installed it backwards. It seems to be the same though so will it really matter? I have the grease niple towards the outside but in the illistrations, it is on the inside near the transmission. I just hate to have to redo it unless it...
  14. C

    Key release lever. What does it do other than...

    My CJ has a manual tilt column thats in decent shape. Its not loose around the tilt or anything abnormal. The only thing is that the key release lever is stuck in the down position. The key can go in and out of the ignition lock as you please. Should I be concerned? Other than this being...
  15. BrockGrimes

    Clutch help

    As you know I recently rebuilt my trans and t-case. I installed poly trans mount and motor mount, so now I notice more noise. But now I hear something from I believe the clutch that sounds like a cicada/locust, clutch chatter? The old mechanical clutch linkage was alot longer. I had to adjust...
  16. BrockGrimes

    Clutch help

    As you know I recently rebuilt my trans and t-case. I installed poly trans mount and motor mount, so now I notice more noise. But now I hear something from I believe the clutch that sounds like a cicada/locust, clutch chatter? The old mechanical clutch linkage was alot longer. I had to adjust...
Back
Top Bottom
AdBlock Detected

I get it, I'm a Jeep owner and ad-block detectors kinda stink but ads are needed on this site. This is a CJ site, all the ads are set for autos (some times others get through.) I cannot make them just for Jeeps but I try.

Please allow ads as they help keep this site running by offsetting the costs of software and server fees.
Clicking on No Thanks will temporarily disable this message.
I've Disabled AdBlock    No Thanks