problems

  1. CJ

    Help Problems getting to site

    We'll get this resolved. To connect please only use (for now) -->> jeep-cj.com Please post problems, state how you connect (phone, PC, tablet etc), browser (Safari, Mozila FireFox, Edge, Chrome, Tapatalk etc.). exact url you used (www.jeep-cj.com, jeep-cj.com, jeep-cj.com/ http://jeep-cj.com...
  2. J

    Clutch Install Problems

    Short Version: 1979 CJ5 with t18 trans had its clutch replaced by myself, a rookie mechanic. After putting it all back together, I go to start it, and my clutch is making a HORRIBLE screetching sound, after a second or two the screetching stops and everything seems "ok," however I can not put...
  3. Sparky1000

    Rough Country lift Problems

    I install a RC 4" lift on my 80 CJ7. I believe the front axle is a 77 or 78 though. I took it out for a quick drive to see how stiff it was going to ride. When I got back, i was looking at the springs and they had been hitting the tie rod and connecting rod. The end link grease fitting on the...
  4. R

    Dana 300 shifting problems

    Ok guys so I just bought a Dana 300 without a shifting lever. I opened it up and everything looks great. My question is how hard is it to shift the forks with a pry bar?? It’s in neutral right now and if I pry on the links to go in 4H only the front catches. I can see it almost catching the rear...
  5. R

    Dana 300 shifting problems

  6. jzak

    Idle Screw Problems

    Hey Guys, Can anyone recommend a way to get off that damn idle screw cone-shaped plug? I tried to drill into it, but the bit just kept wandering. Thanks! Josh
  7. jzak

    Idle Screw Problems

  8. jzak

    Vapor Lock/Heat Soak Problems

    Any time I go on a long trip 1hr+ (Especially in Summer). If I stop the engine for a short period (gas station fillup), when I go to restart it, my CJ rides super rough and stalls out. It eventually comes back to life after stepping on the gas for a while. I'm thinking its a Vapor Lock/Heat Soak...
  9. jzak

    Vapor Lock/Heat Soak Problems

  10. jzak

    LED Headlight Install Problems!

  11. BusaDave9

    Jeep Problems

    Some of you know I had engine trouble in Moab. https://jeep-cj.com/community/threads/moab-2019-trail-report.61496/post-550653 Although Ben offered to help me fix my jeep I got it repaired at a shop owned by a friend. I've been too busy. I got the cam, lifters, pushrods all replaced. We were...
  12. S

    bulkhead wiring Id problems

  13. T

    thread problems

  14. A

    starter problems

    starter continues to engage when key is out. replaced starter,solenoid neutral safety switch.running out of Ideas. Some one said switch out starter switch on column. Any ideas before i go nuts? Ace
  15. Super8mm

    Horn Problems

    I am trying to get my 80 CJ5 ready for a state inspection and I am having a bit of a problem with my horn. The horn works as I used a jumper from the battery and it ground are OK. Next I cant find a spot in the fuse box for a fuse there so I am not sure if there is one or maybe it is on the...
  16. T

    79, 304 cooling problems

    Hello All, I’m new to the site & not computer expert. I am having cooling problems w/304 amc engine on a 79 cj5 SA mostly original. Any help will be appreciated. Rad. cap 16 lds, new rad., new hoses, original water pump & it’s turning & flowing good, checked thermostat & opening at 195...
  17. T

    79, 304 cooling problems

  18. M

    Battery Problems

    Hey So I have 2 brand new Optima Batteries and my alternator is fine. I have checked all of my fuses and I cant find a draw. Ding dong dead after 24hrs of being parked. Starts fine after a jump, and all is good as long as I'm driving everyday. 81 cj7 why you do me so wrong? Anyone with a...
  19. JeffP

    Fuel Gauge Problems

    For those having fuel gauge issues here are some facts. Both the gauge and sending unit resistance range needs to match. (Ohms) Zero to low ohms for full, high resistance for empty. Both the gauge and tank need to be grounded with at least 14 awg wire! If your new gauge reads full all the time...
  20. J

    Clutch Linkage: Release rod and adjuster problems

    If you’ve been following at home, I had a couple problems with my clutch linkage (driver side pivot bracket sheared off the bolts). Upon review of the linkage, bell crank, etc., it looked pretty rough so I ordered a whole new kit for $70. (Before you ask, no I didn’t get the Heim upgrade. Will...
Back
Top Bottom
AdBlock Detected

I get it, I'm a Jeep owner and ad-block detectors kinda stink but ads are needed on this site. This is a CJ site, all the ads are set for autos (some times others get through.) I cannot make them just for Jeeps but I try.

Please allow ads as they help keep this site running by offsetting the costs of software and server fees.
Clicking on No Thanks will temporarily disable this message.
I've Disabled AdBlock    No Thanks