needed

  1. T

    Suspension 1978 CJ7 Frame Rebuild

    I am restoring a 78 CJ7 and I welded new channel inside the frame rails. It came out really well EXCEPT: the frame rails twisted (of course) from the heat. The brainstorm that hit me in order to straighten the rails is to use a Harbor Freight hydraulic porta power and some large all...
  2. raser13

    350 pin out diagram help needed

    Hey guys and gals, i need your help. I'm working an putting a chevy 350 from a 1990 suburban into my CJ-5. I have most of the wiring diagrams for the motor and the ecu. As such i have most of the wiring re-ran since some of the wiring got chewed up by mice. Where i'm running into trouble is...
  3. raser13

    350 pin out diagram help needed

  4. J

    What are these Filters for?

    Can anyone tell me what these 2 supposedly oil filters are? There is a Black hose right behind the transfer case and drive shaft that runs straight to the engine bay. At the end of the hose there are 2 filters. On top of the 2nd filter the line is capped. What is are the two filters for and what...
  5. O

    Photographic help needed: pics or measurements of AMC V8 powered engine bays

    I was wondering if some of you guys would be willing to help me figure out my engine location issue. My Jeep is an 82 model, so the 360 has been swapped in by a previous owner. I feel like it's sitting a bit too far back because the left cylinder head is touching a little piece of metal that is...
  6. O

    Photographic help needed: pics or measurements of AMC V8 powered engine bays

  7. ianjcx

    AMC 304 emissions help needed

    I have a 1975 CJ5 Jeep with an AMC 304 and 3 speed manual. I'm trying to get the vacuum lines hooked up properly but can't seem to find a proper diagram. It was running ok before I tried to make sense of the vacuum lines and now it won't idle at all. Very frustrated, please help.
  8. ianjcx

    AMC 304 emissions help needed

  9. S

    82 Scrambler Rear Axle Assembly Needed

    Looks like I have a bent AMC 20 rear axle on my CJ8. Does anyone know of someone who sells a complete rebuilt rear axle? Or a source for a good rebuildable core? I’m new to jeeps so any advice appreciated! Working out all the gremlins from the previous owner. Jim
  10. S

    82 Scrambler Rear Axle Assembly Needed

  11. B

    Throttle cable help needed please

    It is obvious to me the current throttle cable is not factory plus a hand throttle has been rigged up by the previous owner. I intend to get rid of the hand throttle and have purchased a Pioneer CA-8512 throttle cable. Of course the pedal end hooks up like normal but the carburetor end is a...
  12. C

    Hardtop Part Needed, 84 CJ7

  13. shum8

    Engine wiring harness help needed

  14. M

    Suspension advice needed

    Whats up guys , i have an ol postal jeep ive been doing mods to and I'm just starting to make the suspension more dirt worthy ,I've put together custom leaves, but have the stock main leaf, i want to do a shackle relocation in the rear, along with a longer shackle , while trying to achieve...
  15. J

    Help needed

    I was sitting in the driveway with my Jeep (1964 tuxedo park) idling, the motor sputtered and died. It's never done this before. After it died it'd crank but not start. First thing I thought was fuel, and sure enough no gas in the fuel filter (there is gas in the tank). So I ordered a new...
  16. J

    Help needed

  17. M

    Valve Cover Needed!

    So, 75' 258 4.2L valve covers. It was unknown to me that these things had a notorious leaking issue. I'm slowly figuring out that most of my CJ problems aren't special and many have messed with something similar before. Before I had this realization, I thought I would change out the valve...
  18. M

    Valve Cover Needed!

  19. S

    What is this ticking noise? Help needed please!

    Hi, as always this forum is brilliant. But the other day after a drive out, the jeep started ticking. Brought it home, as you let off acceleration the rhythm doubles. Any help would be massively appreciated. Iv watched some videos on failed lifters. Tried taking the case off and having a look...
  20. S

    What is this ticking noise? Help needed please!

Back
Top Bottom
AdBlock Detected

I get it, I'm a Jeep owner and ad-block detectors kinda stink but ads are needed on this site. This is a CJ site, all the ads are set for autos (some times others get through.) I cannot make them just for Jeeps but I try.

Please allow ads as they help keep this site running by offsetting the costs of software and server fees.
Clicking on No Thanks will temporarily disable this message.
I've Disabled AdBlock    No Thanks