bleeding

  1. J

    New PS pump not bleeding?

    So I installed a new Borgeson PS pump. I put the front end in the air and did the left/right bleed procedure at least 100 times. There is NO power steering at low idle. It starts working around 1,500rpm, but it's sort of twitchy. Took it for a spin around the block and it's no better. Something...
  2. R

    Lots of Bleeding

    I tried searching for solution and i know this has been discussed but I am pulling my hair out on this: I have been working on a cj build (almost 2 years now) and feel like I am spending way too much time trying to get my brakes to bleed. I have put 3-4 big bottles of fluid trying every...
  3. R

    Lots of Bleeding

    I tried searching for solution and i know this has been discussed but I am pulling my hair out on this: I have been working on a cj build (almost 2 years now) and feel like I am spending way too much time trying to get my brakes to bleed. I have put 3-4 big bottles of fluid trying every...
  4. Hamilton172

    Problems bleeding my brakes

    So I just finished installing my new brake lines. Every piece was replaced or rebuilt. Master was cleaned and rebuilt, all T's were cleaned, new flex lines, new hard lines and wheel cylinders. I have been able to bleed both front and the left rear. But the stupid right rear won't bleed! Any...
  5. D

    Bleeding the cooling system-I6

    What's the correct method of bleeding the air from the cooling system? I installed a new water pump, heater core, thermostat and all the hoses. When I started it up I didn't get any coolant flow from the upper hose back into the rad and the temp gauge was going towards the hot. Water does go...
  6. D

    Bleeding the cooling system-I6

    What's the correct method of bleeding the air from the cooling system? I installed a new water pump, heater core, thermostat and all the hoses. When I started it up I didn't get any coolant flow from the upper hose back into the rad and the temp gauge was going towards the hot. Water does go...
  7. C

    Brake Bleeding - Proportioning Valve

    I need to bleed the brakes on a '83 CJ7 I just purchsed. My repair manual says to use special tool "XXXX" on the proportion valve before attempting to bleed. Well of course I do not have that tool nor does the manual say what the tool does so I don't know how to create a work around. I see on...
  8. C

    Brake Bleeding - Proportioning Valve

    I need to bleed the brakes on a '83 CJ7 I just purchsed. My repair manual says to use special tool "XXXX" on the proportion valve before attempting to bleed. Well of course I do not have that tool nor does the manual say what the tool does so I don't know how to create a work around. I see on...
  9. J

    cj5 brake bleeding problems front disc

    so after going thru the front bearings and axle ujoints.... the problem is that i cant seem to bleed the front brakes. to get at the axle i had to remove the caliper but the bolt going thru the banjo fiting on the brake line is traping the bolt holding the caliper on so i had to remove it now i...
  10. Duhwhat

    Hydraulic Clutch soft after bleeding

    To the best of my ability I have bleed the clutch till there is no air and I only have pedal on the bottom third and it is relatively soft. It goes in the forward gears "OK", but reverse has a good grind. I replaced everything in the clutch area when I had it down. I also replaced the...
  11. Duhwhat

    Hydraulic Clutch soft after bleeding

    To the best of my ability I have bleed the clutch till there is no air and I only have pedal on the bottom third and it is relatively soft. It goes in the forward gears "OK", but reverse has a good grind. I replaced everything in the clutch area when I had it down. I also replaced the...
  12. dave123

    Brake bleeding problem

    1975 Cj drum brakes, not power assisted Yesterday, I took the Jeep out. The brakes have been working great, but this time, the pedal went almost to the floor. It was a semi emergency, so I drove the Jeep a little ways like this with no issues rather than the pedal dropping so far down. The...
  13. Allen9878

    Ax15 Bleeding Problems

    I recently installed a ax15 trans on a 258 in my 80 cj5. I have been having problems bleeding it, I have bled it manually a couple times and purchased a pneumatic bleeder and ran that 3 or 4 times. Is there any tricks to bleeding this or is there something else going on? Do I just need to keep...
  14. Allen9878

    Ax15 Bleeding Problems

    I recently installed a ax15 trans on a 258 in my 80 cj5. I have been having problems bleeding it, I have bled it manually a couple times and purchased a pneumatic bleeder and ran that 3 or 4 times. Is there any tricks to bleeding this or is there something else going on? Do I just need to keep...
  15. HighRoller

    Bench Bleeding POS Remaned Mastercylinders

    Ok, my master cylinder was leaking on the back seal so I got a replacement reman one from work (AdvanceAuto). Put the new one in to find out that It was bad as well due to the inner piston not coming all the way back. So I just put the second remaned one in and It's good, Thank :censored: God...
Back
Top Bottom
AdBlock Detected

I get it, I'm a Jeep owner and ad-block detectors kinda stink but ads are needed on this site. This is a CJ site, all the ads are set for autos (some times others get through.) I cannot make them just for Jeeps but I try.

Please allow ads as they help keep this site running by offsetting the costs of software and server fees.
Clicking on No Thanks will temporarily disable this message.
I've Disabled AdBlock    No Thanks