bearing

  1. 407-loco

    Diff Dana 20 solid axle seal

    I noticed my passenger axel is leaking was hoping it was the brakes but not that lucky. Does anyone know of a seal so that the bearing can be an oil bath. I was unaware that it was a packed bearing on the rea axles. Being that it's such a pain to pull and get to just to service the bearing...
  2. Kens1979cj5

    Diff Nitro Gear and Axle One piece axle kit issue

    Anyone have any specs/install/experience info? I ordered the Nitro Gear & Axle 29 Spline Nitro One Piece Narrow Track Rear Axle Kit for AMC Model 20 Jeep CJ5 | CJ7 1976-1983 AXCJS I called Nitro today because there were no specs or install info. I’m a little blown away by the answer I...
  3. O

    TCase T4 to Dana 300

    First off, hello to all. Not much of an internet guy but I have an issue that is giving me some headaches. '83 CJ-7, 258, T4, Dana 300. Put in a new clutch this year and decided that it'd be easier to split the trans and transfer for removal. threw it all back together and, lo and behold, now...
  4. T

    Build Thread new build.

    so we started a new jeep build and started with a 435/300 combo but decided to go auto instead. during the trans. rebuild process i discovered the output bearing is shot...and also is a unicorn. i have found several posts,many part numbers and none match. no parts stores have it or a cross to...
  5. S

    Diff Dana 44 narrow track

    Guy, I'm rebuilding a1977 cj5. I need to replace the amc 20. I have found a dana 44 narrow track. The Pinon is pitted but the housing looks good. I'm not a axle guy, but pretty handy mechanically. Is there anthing special I need to know when I buy the ring gear and pinon? Hope there is a good...
  6. CJ

    OTC 5 Ton Bar Style Puller Set

    After several failed attempts to press a bearing off of an output shaft of my Dana 20 transfer case using a cheap bearing splitter, I decided it was time to invest in some 'real' hardware for my tool collection. I did allot of shopping and decided on a set of tools from OTC - specifically the...
  7. CJ

    Diff Bearing Set-Up Tip.

    Differential set-up quick tip! Don't throw away those old carrier and pinion bearings! Clean them up, then open up the inside with a Dremel tool. Go slow and use a pinion and carrier for test fitting. The goal is to slowly open up the bearing so it slips onto (with a little friction) the pinion...
  8. B

    73 cj5 lift and wheel bearing questions

    I am bringing a 73 Cj5 back to life. Can anybody educate me on how the suspension was setup? I am trying to determine the type of lift on this thing. Right now it is clearing 33x9.50r15 tires. It has 9-10 leafsprings, but that is all I can tell. Also, how hard is it to replace the wheel...
  9. K

    4.2 main bearing bolt

    I have a 4.2 that had a oil leak, pulled the oil pan and found one of the main bearing bolts broke laying in the bottom of the pan. no problem i got an old block i will just get one of those. The bolt will not fit it is a 1/2-13 bolt the one that broke is 7/16-14. Checked everywhere trying to...
  10. K

    4.2 main bearing bolt

  11. KeithMcKalister

    Hydraulic Release (throw out) bearing

    Does anyone have any experience with a product like this? https://www.summitracing.com/parts/ram-78130?seid=srese1&gclid=Cj0KCQjwuZDtBRDvARIsAPXFx3DCkEiQCYnzQ_NDiznxh-T3rDEQTeJTUIMxxabiwmnBEvZ6mOdAf4saAjwqEALw_wcB I'm thinking it may be a better option than fabricating my own bracket for a...
  12. b3uhbp

    T5 install

    Hello all. Just had a catastrophic failure of a bearing on the counter shaft in my T5. I’m told it is a rare break down but that’s my luck. It’s being rebuilt but my question is, when I reinstall it, is it easier to do it with the bell housing attached, or does it really matter? The reason I...
  13. O

    amc 20 axle to bearing play excessive

    Has anyone found an outer axle bearing that was loose in the axle housing? I have that problem with the bearing race is loose in the axle housing. Bearing race is 2.55" outside diameter and the axle hole opening is 2.60". So the bearing race is .05 loose in the axle house. Certainly can't...
  14. O

    amc 20 axle to bearing play excessive

  15. Scout1067

    Bearing Race

    Anybody know the bearing race numbers for a Stock Dana 30? I am having trouble finding the proper race to go with the wheel bearings. I have the new bearings front inner is LMI-102949 and outer is LM-501349. I got these numbers off the old bearings but I don't want to cut my races out until I...
  16. Scout1067

    Bearing Race

  17. S

    Dana 30 Bearing / Seal Kit

    Does anyone have the Timken or Skf part#'s for bearings, seals and related parts to rebuild the hub & spindle? I'm getting ready to replace ball joints and axle u-joints and figured its a great time to refresh it all. This is on a 79 CJ5 Dana 30
  18. S

    Dana 30 Bearing / Seal Kit

  19. B

    Clutch/pilot bearing

    So, I have a 1980 cj5 4 cyl with the sr4 trans. I'm currently in the middle of installing a new clutch kit and I've ran into an issue. The new pilot bearing and the old one do not match. But, I'm not sure the old one is even correct. I bought this jeep with a clutch issue, and once I got...
  20. B

    Clutch/pilot bearing

Back
Top Bottom
AdBlock Detected

I get it, I'm a Jeep owner and ad-block detectors kinda stink but ads are needed on this site. This is a CJ site, all the ads are set for autos (some times others get through.) I cannot make them just for Jeeps but I try.

Please allow ads as they help keep this site running by offsetting the costs of software and server fees.
Clicking on No Thanks will temporarily disable this message.
I've Disabled AdBlock    No Thanks