Welcome to Jeep-CJ.com
 Jeep CJ Community and General Off-Road Site |
|
Become a Member and remove this add!
|
May 08, 2011 - 11:49 AM - by billyocup
|
I traded my nephew a 12' fishing boat & trailer for this 75 CJ5 back in December. I knew going in that I was going to take it down to the frame and start over. Besides a general clean up it needed a new brake system, new wiring harness, steering work, new tires, and who knows what else until I started tearing it apart. My goal is to build a reliable trail rig. I want it street legal, but most of the time it will be used off road.
I needed to have a decent place to work on it, so I spent most of January working on the garage (insulation, sheetrock, lighting, more electrical and storage space for my wife's craft stuff). Moved the Jeep into the garage the 1st of Feb. and started taking it apart.
Being new to Jeeps, it took me awhile to sort out exactly what I have - 75 CJ5, 304 V8, T15 trans, Model 20 TC, Dana 44 rear & Dana 30 front with 3:73 gears. It has an existing 2 1/2 inch Rancho lift on it and 33x12.5x15 tires. The tub is steel with a little minor rot and the front end is a one-piece fiberglass unit.
The photos are from the 1st... [Read More]
|
|
|
May 28, 2009 - 7:14 PM - by Petescj
|
People have been asking me what my plans are for the Scrambler and if Im going to do a build thread. Ive been thinking about it a little while now and have a decent plan in mind. Its not going to be anything radical or off the wall but Im going to chronicle it here. Over the weekend I'll post more pics and give you guys an idea where Im headed. For now heres the starter pic:
|
|
|
Dec 27, 2010 - 11:38 PM - by myjeepsbigger
|
Not sure if it's taboo around here or not, but I'm in the process of putting a 2001 5.3L GM V8 in my CJ...and since I'm a newbie to this site, I figured I would share. My goals for this rig is to have a VERY reliable, strong, driver that can hit and occasional MILD trail (I have a full tube buggy on one-tons that I can use for the hardcore stuff...but trailering it everywhere just sucks.).
I added this CJ to my fleet of Jeeps early this past summer. It had been sitting in the weeds for a couple years and was suffering from severe neglect. Some birds had made the grille and heater housing into a sparrow condo and there were other unmentionable critters living in it as well. I trailered it home and had it running the same weekend (battery, starter solenoid, fuel pump, cleaned fuel tank, water pump, some lighting and electrical repairs). It was pretty rusty and a little beat up, but in surprisingly good condition considering its past. My girlfriend and I cruised it all over the place through the summer (and did some light wheelin), but the 258 just wasn't doing it... [Read More]
|
|
|
Feb 04, 2011 - 1:50 AM - by Stormrider
|
I just bought this 77 Golden Eagle and I am planning on restoring it real soon so I figured I'd go ahead and start my build thread.
It has a 304 V8, T4, Dana 20, Dana 30. The nice thing about it is that it has a fiberglass tub, hood, and fenders so not to much rust to worry about. The frame is solid....it just has surface rust.
I am on a budget so I will be doing most of the work myself. I do have a good mechanic friend that will help out and let me use the lift at his shop and not charge me and arm and a leg. I also have a buddy that's a retired bodyman that is going to do the paint job for me cheap.
The first thing that I am going to do is pressure wash the HELL out of it! It has mud and dirt everywhere. I plan on cleaning up the motor, painting it, and replacing whatever is needed. I will also redo the whole interior, since it doesn't have much.....at least nothing that I can reuse. I also plan on replacing the lift kit since the one on it now is pretty worn out. Last thing would probably be getting it painted. Not sure if I am sticking... [Read More]
|
|
|
| 13 members and 417 guests |
| 73CJ, bdunnam, cigarette1, coldair, fishinfool98, gianjeep, hagar, IOPort51, itakeprozac, Jake, jasonmark1993, OldC7, wulfsbergvw |
| Most users ever online was 829, 03-31-2011 at 12:46 PM. |
Welcome to Jeep-CJ.com, a community devoted to one of the greatest and most loved off-road vehicles ever produced. No matter what CJ you own or are interested in, we want this to be your favorite place for information and fun. Jeep-CJ.com was created with CJ and Jeep owners, as well as all off-roaders in mind.
This site's main purpose is to give all CJ owners and lovers a community to discuss and show off their rigs. Jeep-CJ.com was developed as a member owned community, it's 'your' site. Members have control of the content and design and the majority of Jeep-CJ.com is fully customizable. (LOOK HERE)
While we do focus on the CJ model of Jeep's, this site is not limited to this alone. If you are an Off-Road enthusiast, feel free to join; all membership is welcomed.
Jeep-CJ.com is run by a long time CJ owner (28 years) so you know that I share the same passion as other fellow CJ enthusiasts.
Please take a moment to register and look around. It's quick and absolutely free!
--CJ
|
|
|
| |
 10-02-2008 05:11 PM |
 |
Admin & Owner
|
Views: 2,579
Replies: 0
|
|
For years I have been missing one of the original windshield hold down clamps for my CJ5. I have searched for replacements but never have found any thing that functions as well.
After placing an add here at Jeep-CJ.com I was informed that AA sold replacements and knowing what quality products that AA is known for, I thought I would order a set - sight unseen.
The order transaction went smoothly and within minutes a new set of hold downs (#176127) were on their way. A five day delivery time w... [Read More]
|
|
11-12-2010 08:38 AM |
|
New Jeeper
|
Views: 997
Replies: 0
|
|
These Shackle Hangers are HEAVY DUTY! Milled out of a solid block of steel. Mount with 3 bolts instead of 2 like stock hangers do. Front uses existing hole already in the frame. Rear needs extra hole drilled (I used a 21/36 bit) and the frame had slots on each side where the new hole was drilled so I was about to put the bolt through the slot in the frame and through the hole and get it bolted up. They cost $145.08 for the set of 4 with grade 8 mounting hardware. Worth every penny!
... [Read More]
|
|
03-26-2009 07:30 PM |
|
Admin & Owner
|
Last Reply:
CJ
03-28-2009 09:56 PM 
|
Views: 1,999
Replies: 2
|
|
After several failed attempts to press a bearing off of an output shaft of my Dana 20 transfer case using a cheap bearing splitter, I decided it was time to invest in some 'real' hardware for my tool collection.
I did allot of shopping and decided on a set of tools from OTC - specifically the 4518 kit. It's collection of assorted bars and two different size splitting blocks suited my needs perfectly.
... [Read More]
|
|
|
|
08-14-2010 04:20 AM |
|
New Jeeper
|
 |
Views: 1,109
Replies: 0
|
|
This is a new club/forum that just launched. It caters to North East Florida and surrounding areas. We don't care where you live, all that matters is that you are a 4x4 enthusiast. Come join and make the community bigger and add to the knowledge we are trying to create.
The sites address is Http://www.NorthEastFL4x4.com so come join and participate now!
|
|
12-11-2009 03:38 PM |
 |
New Jeeper
|
Last Reply:
MountainMan
12-11-2009 05:38 PM
|
|
Views: 2,290
Replies: 1
|
|
We jeep all over Western US. Have over Four Hundred members.
Family type club. Strict Forum rules!
See us at http://www.LSJC.org
|
|
07-17-2011 12:03 AM |
|
New Jeeper
|
 |
Views: 131
Replies: 0
|
|
We're a bunch of enthusiasts who don't have hundreds of thousands of dollars to dump into our hobbies. We have build days, barbeques, we drink beer, shoot guns (not in that order usually), we have military and civilian members and we are pro family and pro America. Come and wheel with us.
|
|
05-05-2009 05:12 PM |
 |
Junior Jeeper
|
|
Views: 2,137
Replies: 0
|
|
We are a fellow off-road community that welcomes anything off-road, even mall-crawlers. Our site is not child friendly so be careful when browsing (PG-13 to R rated profanity / non-nudity). We welcome anyone in the area to join us for rides, and meet and greets!
|
|
|
|
|
|
|
|
|
|
