stroker

  1. C

    Anyone building a stroker from a 4.0?

    I have internals from my 4.2 that could be used on a stroker project. In particular, I have the crankshaft. Of course I have the pistons, etc. as well.
  2. J

    I am needing some informational help

    I recently got a 99 jeep grand cherokee limited with a 4.7L V8 engine and it is full stock. I also found but have not purchased yet a 4.7L I8 stroker and was wondering if the 2 are interchangeable without having to modify the transmission bell housing. If they are not then what engines are...
  3. Az84cj7

    Stroker motor

    Anyone have some good or bad info on doing a i6 stroker motor.? I've been kicking it around.
  4. Az84cj7

    Stroker motor

    Anyone have some good or bad info on doing a i6 stroker motor.? I've been kicking it around.
  5. ThisGuyUKnow

    The "Pig in a Poke" Stroker

    Ok so strap in for a long story. I have been getting pretty sick with the TPI AMC 360 project's BS. I'll get it running then it will mysteriously stop with no reasonable explanation. This last time was just the straw that broke the camel's back as the process has been going on for almost 6...
  6. R

    Stroker long block at Jeg's

    Spotted this in the Jeg's wish book today. Blueprint Engines BP2870CT Blueprint Engines Jeep 4.0L Stroker Engine Not too bad a deal for a blueprinted and balanced stroker engine. They don't list the bore size, but I would guess .030" over. It wouldn't be hard to spend $2895 on an engine...
  7. R

    Stroker long block at Jeg's

    Spotted this in the Jeg's wish book today. Blueprint Engines BP2870CT Blueprint Engines Jeep 4.0L Stroker Engine Not too bad a deal for a blueprinted and balanced stroker engine. They don't list the bore size, but I would guess .030" over. It wouldn't be hard to spend $2895 on an engine...
  8. Rescue Diver

    Thread exclusively to discuss the best ways to build Jeep I6 Stroker motors

    Let's try this again. In this thread, I would like to share what I'm doing, and get input from others specifically pertaining to ways to build 4.6 and 4.7 liter Inline 6 stroker motors. I decided to pull the trigger on starting my stroker motor project. I'm picking up a good 1995 4.0 donor...
  9. Rescue Diver

    Thread exclusively to discuss the best ways to build Jeep I6 Stroker motors

    Let's try this again. In this thread, I would like to share what I'm doing, and get input from others specifically pertaining to ways to build 4.6 and 4.7 liter Inline 6 stroker motors. I decided to pull the trigger on starting my stroker motor project. I'm picking up a good 1995 4.0 donor...
  10. Rescue Diver

    Jeep Stroker Inline Six 4.6L and 4.7L thread

    I decided to pull the trigger on starting my stroker motor project. I'm picking up a good 1995 4.0 donor motor today or tomorrow, and over time I will pick up new Sealed Power dished pistons that should give me roughly 9.25 to 1 compression, getting the block bored either 30 or 60 over, and I'll...
  11. Rescue Diver

    Jeep Stroker Inline Six 4.6L and 4.7L thread

    I decided to pull the trigger on starting my stroker motor project. I'm picking up a good 1995 4.0 donor motor today or tomorrow, and over time I will pick up new Sealed Power dished pistons that should give me roughly 9.25 to 1 compression, getting the block bored either 30 or 60 over, and I'll...
  12. S

    4.0 stroker swap

    hey everyone id love it if u guys could give me some advise on this as i think im geting in over my head... im so far out of my knowledge base with this thing that im having to do research to find out what questions to ask so bare with me and i have learnt so much that just thinking about my...
  13. S

    4.0 stroker swap

    hey everyone id love it if u guys could give me some advise on this as i think im geting in over my head... im so far out of my knowledge base with this thing that im having to do research to find out what questions to ask so bare with me and i have learnt so much that just thinking about my...
  14. I

    4.2 / 4.0 "stroker" build...need a few answers

    I am yanking the motor out and doing below. Anyone have some answers to the questions I have below? 1. "Stock" 258 short block bored .030 2. 4.0 clearwater head (what rockers? 4.0 or 258 push rods?) 3. 4.0 intake (what year? what fuel rail? what lb injectors?) 4. 4.0 exhaust header...
  15. I

    4.2 / 4.0 "stroker" build...need a few answers

    I am yanking the motor out and doing below. Anyone have some answers to the questions I have below? 1. "Stock" 258 short block bored .030 2. 4.0 clearwater head (what rockers? 4.0 or 258 push rods?) 3. 4.0 intake (what year? what fuel rail? what lb injectors?) 4. 4.0 exhaust header...
  16. B

    Stroker motor ???s

    I have been porring over jeep sites in my free time and came upon the stroker idea gone using a 4.0 head on a 258 , have any of you cone this route? What are the pros and cons that you dealt with? From what I have read a .060 overbore would bump a 258 to 4.6 or 4.7 l from 4.2. Would like to...
  17. B

    Stroker motor ???s

    I have been porring over jeep sites in my free time and came upon the stroker idea gone using a 4.0 head on a 258 , have any of you cone this route? What are the pros and cons that you dealt with? From what I have read a .060 overbore would bump a 258 to 4.6 or 4.7 l from 4.2. Would like to...
Back
Top Bottom
AdBlock Detected

I get it, I'm a Jeep owner and ad-block detectors kinda stink but ads are needed on this site. This is a CJ site, all the ads are set for autos (some times others get through.) I cannot make them just for Jeeps but I try.

Please allow ads as they help keep this site running by offsetting the costs of software and server fees.
Clicking on No Thanks will temporarily disable this message.
I've Disabled AdBlock    No Thanks