removal

  1. S

    Need input on front rotor removal

    Hello Everyone! I am a new member to the forum and this is my first post. I have a 1980 CJ-5 and I need to replace the front brake rotors. I have read many forum posts as well as the Haynes manual about doing this. Everything I have read says that once the locking hub and the locking...
  2. S

    Need input on front rotor removal

  3. J

    AMC 20 diff questions. Hun removal, seals

    Can someone help me out that has been through an AMC 20 rear end. I pulled the hubs with a puller and the axle shaft came with it. I thought these were 2 piece so after that I put a 3 jaw on the hub and cranked on it with my 3/4 impact... nothing. Heated with torch... nothing. Am I missing...
  4. J

    AMC 20 diff questions. Hun removal, seals

  5. gert

    Easiest bushing removal method ever

  6. N

    Dana 300 Removal

    I'm in the process of pulling out my D300 for a rebuild. Everything has been disconnected and I've broken all the bolts loose holding the TC to the tranny except the one located on top (12 o'clock position).. Any ideas on the best way to get to that bugger? I can't ever see it yet alone get up...
  7. N

    Dana 300 Removal

  8. J

    86 CJ7 wiper linkage disassembly question and bracket removal tips.

  9. Manic Mechanic

    windshield washer nozzle removal

  10. Tremelune

    Body lift removal + 4° caster = heeeavy steering

    I have an '83 CJ7 I've been trying to correct the steering on, and I've hit a snag...After removing a 2" body lift and adding 4° caster shims (for a total of 6.5°), my steering went from very light to very heavy. I'm aware that increasing caster makes steering more difficult, but I think...
  11. J

    Exhaust manifold stud removal

    Amc 360...Long story short, I'm swapping from headers to stock manifolds. The studs where the exhaust pipes bolt to broke during removal. It's a blind hole. What's the best way to remove the broken studs? Ease out, or is there a better option? Sent from my iPhone using Tapatalk
  12. J

    Exhaust manifold stud removal

  13. J

    Freeze plug sensor removal

    Good day all, in a jam. Still trying to finish my 77 before the snow flies, (its lightly snowing right now....) I just added the Mojave heater core, plumbing looks good, blower works, pictures to come, I wanted to add a block heater while I was at it, my block has 3 freeze plugs all drivers...
  14. J

    Freeze plug sensor removal

  15. V

    Roll bar removal

  16. Scout1067

    Bolt Removal question

  17. K

    Unnecessary stuff removal guide

    Hey y'all, I've got a 1980 CJ7, 258 I6, SR4 4 speed manual. What I'm looking for instructions/recommendations for what all I can remove/simplify on my Jeep. I drive it round trip maybe 30 miles a week just to work and back. It's a 3rd vehicle so I'm not depending on it. I don't need great gas...
  18. K

    Rear wheel cylinder removal

  19. N

    '77 CJ7 Dash Bulb Removal Help

  20. MikeyBobby

    Removal turn/parking light

Back
Top Bottom
AdBlock Detected

I get it, I'm a Jeep owner and ad-block detectors kinda stink but ads are needed on this site. This is a CJ site, all the ads are set for autos (some times others get through.) I cannot make them just for Jeeps but I try.

Please allow ads as they help keep this site running by offsetting the costs of software and server fees.
Clicking on No Thanks will temporarily disable this message.
I've Disabled AdBlock    No Thanks