chevy

  1. I

    Engine 151 duke

    I'm in need of a 151 iron duke that runs in Illinois that can be bought cheaply. My cj7 engine is hurt and it's my daily driver it's running on 3 cyl right now engine is very tired block is worn out and head is also. Need to find one in the next few days. I can be found at greenhotrod2@gmail.com...
  2. Peanut Butter

    TH400 Technical Information

    This Jeep TH400 Technical Information thread is based on information that I have gathered after discovering that my own TH400 was not a Chevy housing but a BOP Housing from a Cadillac. The Turbo Hydromatic 400 automatic transmission was found in Jeep CJs from 1976 to 1979. It was only in the...
  3. mdeluca

    Small Block Chevy Powered Jeep CJ's in the Dunes

    Pretty cool...!!! https://www.youtube.com/watch?v=qQQkg7l4tiQ
  4. OldZeke

    Chevy ignition to Ford harness in my CJ!

  5. squishware

    looking for input (chevy content)

    I need to replace the charcoal canister. My '82 CJ7 has a Chevy 4.3 V6 TBI. I found a two port evap canister for the 89 S10 my motor came from. I found a vacuum schematic showing one line to tank and one to TBI. Will this work or will I have crazy gas odor?
  6. squishware

    looking for input (chevy content)

  7. raser13

    chevy 350 wiring, what all do i need

    hey guys and gals, have a 1990 chevy 350 from a suburban that was just given to me. i'm working on getting it into the cj5. i've been trying to find all the important items for the 350. it has a throttle body on it. you know the half carb, half fuel injection thing. i've taken all of the wiring...
  8. raser13

    chevy 350 wiring, what all do i need

  9. raser13

    chevy 350 pilot bearing/pushing help

    hey guys and gals, i have a chevy 350 out of a 1990 suburban that i got for free. it originally was attached to an auto trans. now it's going to be mated to my t-176 stick. what pilot bushing would i need? my jeep came with a 350 originally but it kept having issues. so i pulled that and...
  10. raser13

    chevy 350 pilot bearing/pushing help

  11. B

    Chevy 350

    Can anyone tell me if it matters where the heater hoses are connected? I have one coming out of the manifold and one out of the water pump. Thanks!
  12. B

    Chevy 350

  13. raser13

    Chevy 350 help

    Hey guys and gals, it's been a whole since I've been active here. My cj 5 has had a blown motor a 258 for some time now and has been sitting. We haven't had the money to get a new motor. But I've still been here watching in the shadows. But my luck has changed for the better. I responded to an...
  14. raser13

    Chevy 350 help

  15. J

    WANTED: Thermostat Housing

    Does anybody know where I can find this thermostat housing? I have done a lot of research on this subject and found that the same engine model that is in my Jeep is also from a Buick, Chevy Truck, and Pontiac. This housing is very hard to find based on my knowledge and any help would be...
  16. B

    Wiring up chevy 350

    Ok,so i have been looking at posts for the last couple weeks on wiring for chevy 350 conversion. I'm looking for a dwg of some sort to help me and although i've seen alot of them i'm slightly confused. the motor is now installed and it looks like i have the same alternator as what is on the 350...
  17. B

    chevy 350 conversion question

    the Chevy 350 i have does have the long water pump.Do i need to switch that over to the short water pump? looks like roughly its about an 1.5" of difference. if i have to switch it out i guess nows the time so i can start looking for all the other stuff i will need to do it. Thanks in advance !!!
  18. B

    chevy 350 conversion question

    the Chevy 350 i have does have the long water pump.Do i need to switch that over to the short water pump? looks like roughly its about an 1.5" of difference. if i have to switch it out i guess nows the time so i can start looking for all the other stuff i will need to do it. Thanks in advance !!!
  19. Lilredwagon

    283 Chevy small block valve covers

    Hello, I'm rebuilding my engine and I need new valve covers. I want a set with a PVC/valve. Mine have offset bolt holes which seem to make my part shopping a bit more challenging. My local parts guy said my small block probably came out of something 1957 or older. He can get me a set but they...
  20. Lilredwagon

    283 Chevy small block valve covers

    Hello, I'm rebuilding my engine and I need new valve covers. I want a set with a PVC/valve. Mine have offset bolt holes which seem to make my part shopping a bit more challenging. My local parts guy said my small block probably came out of something 1957 or older. He can get me a set but they...
Back
Top Bottom
AdBlock Detected

I get it, I'm a Jeep owner and ad-block detectors kinda stink but ads are needed on this site. This is a CJ site, all the ads are set for autos (some times others get through.) I cannot make them just for Jeeps but I try.

Please allow ads as they help keep this site running by offsetting the costs of software and server fees.
Clicking on No Thanks will temporarily disable this message.
I've Disabled AdBlock    No Thanks